Servo motor z oljčnim oljem s štirimi glavami bat polnjenje ROPP kovinske kapice dvojne strani stroji za etiketiranje kvadratne steklenice polnilna linija popolnoma avtomatska

Opis

The line specially designed for our russian customer who sent to us the glass bottles (thin&tall) is suitable for food packing industry like olive oil/wine bottles fill-cap-label process.

Samples offered by our EU customer

The whole line including filling capping labeling machine

1.model NPACK-5030 piston filling machine
2.model NPACK-AC40 ROPP capping machine
3.model NPACK-650A double sided labeling machine
4.Nitrogen gas flushing function after filling
5.Accumulation turntable for collecting final product

As below there is the basic description &introduction one by one :

►Model NPACK-5030 four heads piston filling machine

The 4heads olive filling machine,controlled by the microcomputer,combines the photoelectricity with pneumatic operation,

thus widely is applied for the liquid filling of the agriculture chemical、solution、liquid detergent、cosmetic as well as olive.The filling volume is precise,foamless and stable.

The machine can fill the liquid with the range from 25-1000ml,meanwhile there is no special requirement on the shapes of bottles.That is to say,it can fill the liquid for the normal bottles as well as the irregular-shaped bottles.

Model       NPACK-5030

Filling range     50～3000ml

Filling speed　       ＜20-30b/m（for 500-1000ml liquid）

Natančnost ± 1%

Moč / napajanje Suppy 0.8kw 、 220v

Delovni tlak 5 ～ 6kg / cm3

Air consumption　  0.5-0.7mpa

NW 500kg

Outer dimension      2000×800×1900mm

Mark:The filling nozzles can be designed and manufactured according to requirements from customers on the filling range and filling speed

Filling speed adjustment

Filling speed adjustment has the following 6 factors:

1, the speed of the product is determined by the viscosity of the product and the length of the suction pipe.

2, filling speed depends on the diameter of the filling head, the diameter is large, the speed is quick.

3, the product of the bubble level. The product filling speed of the high bubble should be slowed down.

4, how much is the filling quantity.

5, the accuracy of the filling quantity, adjust the filling time of each cast.

6, adjust the filling speed (that is, the speed of the servo motor).

General trouble shooting and processing

1）Touch screen is not shown, but the indicator light

Fault cause:

Check whether the fuse is burning, or the contact is bad, replace or reinstall the fuse.

2）The output indicator of the programmable controller has an output indicator, but the solenoid valve does not work.

Fault cause:

Upon examination of the solenoid valve failure, is the key to the programmable controller in the electrical damage, can replace the same type of intermediate relay, fault can be ruled out (this fault is very rare).
3）The main head there is a leak in the shutdown.

Fault cause:

The filling head cylinder does not move up and down, replaced PTFE head, check on the stingy joints have gas, or replace the filling valve, can be ruled out

4）After filling in a number of bottles do not fill

Fault cause:

♦Check whether the bottle counting electric eye, if not counting adjustable electric distance, so that it can reach the count;

♦ Check that the liquid level indicator is black, if it is white, and the liquid level is fluid, and can be filled with black

♦ Check the magnetic switch cylinder after the dive, the light is bright, if not bright, adjust to the light.

♦Check the back of the servo motor is close to the switch is bright, if not bright, adjust to the light.

5)Individual valve or cylinder action to slow down or do not work.

Fault cause:

♦The general situation is caused by the fault of the control valve, first check to control the output of the output of the display lamp (in the lower left of the programmable controller) work is normal, confirm the normal operation of the following check.

♦Magnet coil plug for transposition of the solenoid valve, if change the position of the fault, indicating that the electromagnet coil is damaged, replace the coil after failure can be ruled out.

If the valve group of the emptying port does not stop to have a lot of gas, the system has a more serious leakage. Can check the internal sealing condition, if damaged, should be replaced. If the fault can not be ruled out, can check the valve spool movement, see if there is a card phenomenon or the seal is damaged, and repair, if damaged more serious, it should be replaced by the entire valve.

6）Servo motor alarm.

Fault cause:

♦Check whether the PLC on the F**, if it is to turn off the power, and then open up to manual operation, a number of seconds after the manual injection, and then press the manual back to zero.

►Nitrogen gas flushing system

NPACK-AC40 Automatic ROPP capping machine for olive bottle with metal caps with protective chamber

avtomatski stroj za zapiranje ROPP s sistemom za nadzor gumbov

Pokrivne glave za ROPP pokrov

Stroj za zapiranje je primerna oprema za stiskanje z valjanjem aluminijastih pokrovčkov za plastično steklenico, steklenico za hišne ljubljenčke in steklenico. Predoblikuje pokrovček za steklenico pod valjanjem s kuhalnimi ploščami, samodejno dovaja steklenico 、 Pokrovčki, odstranjevanje hrbtnih pokrovčkov. Zamaščena plastenka daje prednost značilnostim, kot je stabilen učinek za zapiranje, priročno zapenjanje, tako da deluje kot ponarejeno in proti kraji

Model NPACK-AC40

Dovodni prah (V / Hz) AC 220/50 380/60

Zmogljivost (m / min) ≧ 4000B / M

Velikost pokrovčka (mm) 250-1000

Uporaba Alum-pokrovčki

Zračni izpuh iz vakuumske črpalke (m3 / h) 5KG

Zunanja dimenzija （L × Š × V mm (mm) 2000 × 1000 × 2300

NG (kg) 520

Risba delovnega procesa z omejevanjem ROPP (vzemimo primer kot avtomatska linija s transportno platformo)

How to operate model NPACK-C25 Single head ROPP capping machine

Kontejner za dovod, ki se premika po tekočem traku, se skozi nakladalni polž, zvezdno kolo, ki posodo spusti pod tesnilno glavo, v naslednjem indeksirnem delu dovaja posodo za potisno polnjenje, pomeni, medtem ko med steklenicami pokrovček zaboj iz dovodnega žleba polni pokrov posodo, kjer sta telo in vrat posode nameščena pod vrtečo se glavo, kjer tesnilna glava odlično deluje z navojem in tesnjenjem.

Izrazite lastnosti:

Enota je narejena kompaktno in vsestransko.
SS Slat transporter
SS elegantno mat dodelano telo
Vgrajena prednja nadzorna plošča
Vibracijska posoda
S frekvenčnim pogonom A / c

►model NPACK-650A double sided labeling machine

The labeling equipment is for the round bottle labeling in the industry like food、oil、pharma、wine、cosmetics and so on.

The machine with elegant design can be easily operated and maintained by the common worker,

who requires no special training in operation this machine.Just give a simple adjustment to produce another product when you want to swap the different kinds bottle labeling.

Metal caps capping+labeling line

The bottle labeler is thus out from as below-mentioned characteristics:

1: Glavni del opreme je izdelan iz SUS304 in naprednih izdelkov iz aluminija.

2:The labeling heads is driven by the stepping motor that is imported from Japan.

3: Vsa oprema svetlobnih senzorjev je uvožena iz Japonske in Nemčije

4: PLC Nadzoruje vmesnik človek-stroj s 60 pomnilnimi enotami

5: Stroj je najboljša izbira za delovanje posameznega delavca.

6: Stroj ima funkcijo tako, da se drži steklenic, tako da razdeli steklenice, "označi", tako da šteje in šteje.

7: Kot 、 višine 、 kota označevanja je mogoče enostavno nastaviti.

8: Stroj je opremljen s tekočim trakom, ki je nameščen na proizvodni liniji.

Basic parameter of double sides labeling machine

turntable for accumulation of final product